View T315XW03-V3_7748740.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 1 / 30 free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 2 / 30 contents no contents record of revisions 1 general description 2 absolute maximum ratings 3 electrical specification 3-1 electriacl characteristics 3-2 interface connections 3-3 signal timing specification 3-4 signal timing waveforms 3-5 color input data reference 3-6 power sequence 3-7 backlight specification 4 optical specification 5 mechanical characteristics 6 reliability test items 7 international standard 7-1 safety 7-2 emc 8 packing 8-1 definition of label 8-2 packing methods 8-3 pallet and shipment information 9 precautions 9-1 mounting precautions 9-2 operating precautions 9-3 electrostatic discharge control 9-4 precautions for strong light exposure 9-5 storage 9-6 handling precautions for protect film free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 3 / 30 record of revision version date page description 0.1 2009/09/29 first release 0.2 2009/11/23 22 update front view drawing 23 update back view drawing 25 update panel label 1.0 2009/12/25 6 update lcd power consumption max:4.32 watt 6 backlight power consumption: max:81.9 , min:74. 1 15 external pwm frequency: typ. 150 hz 21 bezel opening : horizontal 703.8 mm, vertical 398.4 mm 22 update front view drawing 23 update back view drawing 24 drop test (with carton) height: 45.7 cm , 1 corner, 3 edges, 6 surfaces (astm-d5276) 28 pallet after packing : 1150(l)mm*840(w)mm*1222 (h)mm free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 4 / 30 1. general description this specification applies to the 31.5 inch color t ft-lcd module t315xw03 v3. this lcd module has a tf t active matrix type liquid crystal panel 1,366 x 768 pixels, and diagonal size of 31.5 inch. this modul e supports 1,366 x 768 mode. each pixel is divided into red, g reen and blue sub-pixels or dots which are arranged in horizontal stripes. gray scale or the brightness of the sub-pixel color is determined with a 8-bit gra y scale signal for each dot. the t315xw03 v3 has been designed to apply the 8-bi t 1 channel lvds interface method. it is intended t o support displays where high brightness, wide viewin g angle, high color saturation, and high color dept h are very important. * general information items specification unit note active screen size 31.5 inch display area 697.685 (h) x 392.256(v) mm outline dimension 760.0 (h) x 450.0 (v) x 46.9(d) m m with inverter driver element a-si tft active matrix display colors 8 bit, 16.7m colors number of pixels 1,366 x 768 pixel pixel pitch 0.51075 mm pixel arrangement rgb horizontal stripe display operation mode normally black surface treatment anti-glare, 3h haze=11% free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 5 / 30 2. absolute maximum ratings the followings are maximum values which, if exceede d, may cause faulty operation or damage to the unit item symbol min max unit conditions logic/lcd drive voltage vcc -0.3 14 [volt] note 1 input voltage of signal vin -0.3 4 [volt] note 1 operating temperature top 0 +50 [ o c] note 2 operating humidity hop 10 90 [%rh] note 2 storage temperature tst -20 +60 [ o c] note 2 storage humidity hst 10 90 [%rh] note 2 panel surface temperature pst - 65 [ o c] note 3 note 1: duration:50 msec. note 2 : maximum wet-bulb should be 39 and no conde nsation. the relative humidity must not exceed 90% non-conde nsing at temperatures of 40 or less. at temperature s greater than 40 , the wet bulb temperature must not exceed 39 . note 3: surface temperature is measured at 50 dry condition free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 6 / 30 3. electrical specification the t315xw03 v3 requires two power inputs. one is e mployed to power the lcd electronics and to drive t he tft array and liquid crystal. the second input for blu is to power inverter. 3-1 electrical characteristics value parameter symbol min. typ. max unit note lcd power supply input voltage v dd 10.8 12 13.2 v dc 1 power supply input current i dd -- 0.3 0.4 a 2 power consumption p c -- 3.6 4.32 watt 2 inrush current i rush -- 2 3 a 3 differential input high threshold voltage v th -- -- +100 mv dc 4 differential input low threshold voltage v tl -100 -- -- mv dc 4 lvds interface input common mode voltage v icm 1.1 1.25 1.4 v dc 4 input high threshold voltage v ih (high) 2.7 -- 3.3 v dc -- cmos interface input low threshold voltage v il (low) 0 -- 0.6 v dc -- backlight power consumption p bl 74.1 78 81.9 watt -- life time 50,000 -- -- hours 8 note : 1. the ripple voltage should be controlled under 10% o f v cc 2. test conditi on: (1) v dd = 12.0v (2) fv = 60hz (3) f clk = 82 mhz (typ.) (4) temperature = 25 (5) test pattern : white pattern 3. measurement condition : rising time = 400us gnd gnd gnd gnd v vv v dd dddd dd 10% 90% 400 400400 400 s free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 7 / 30 4. v icm = 1.25v v vv v th thth th v vv v icm icm icm icm v vv v tl tltl tl 0 00 0v vv v 5. input channel pair skew margin 6. do not attach a conducting tape to lamp connecting wire. if the lamp wire attach to conducting tape, tft-lcd module have a low luminance and the inverte r has abnormal action because leakage current occurs between lamp wire and conducting tape. 7. the relative humidity must not exceed 80% non-conde nsing at temperatures of 40 or less. at temperatures greater than 40 , the wet bulb temperat ure must not exceed 39 . when operate at low temperatures, the brightness of ccfl will drop and the life time of ccfl will be reduced. 8. specified values are for a single lamp only which i s aligned horizontally. the lifetime is defined as the time which luminance of the lamp is 50% compared to its original value. [operating condition: continuous operating at ta = 252 ] free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 8 / 30 3-2 interface connections ? lcd connector - ffc connector on source board : p-t wo 196282-30041 pin no p-two 196282-30041 1 reserved no connect ( auo internal use) 2 reserved no connect ( auo internal use) 3 reserved no connect ( auo internal use) 4 gnd ground 5 r_0- lvds channel, signal 0- 6 r_0+ lvds channel, signal 0+ 7 gnd ground 8 r_1- lvds channel, signal 1- 9 r_1+ lvds channel, signal 1+ 10 gnd ground 11 r_2- lvds channel, signal 2- 12 r_2+ lvds channel, signal 2+ 13 gnd ground 14 r_clk- lvds channel, clock - 15 r_clk+ lvds channel, clock + 16 gnd ground 17 r_3- lvds channel, signal 3- 18 r_3+ lvds channel, signal 3+ 19 gnd ground 20 reserved no connect ( auo internal use) 21 lvds_sel open/high(3.3v) for ns, low(gnd) for jeida 22 reserved no connect ( auo internal use) 23 gnd ground 24 gnd ground 25 gnd ground 26 v dd operating voltage supply, +12v dc regulated 27 v dd operating voltage supply, +12v dc regulated 28 v dd operating voltage supply, +12v dc regulated 29 v dd operating voltage supply, +12v dc regulated 30 v dd operating voltage supply, +12v dc regulated free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 9 / 30 ? lcd connector - lvds connector on transfer board : starconn 093g30-b0001a-1 pin no. starconn 093g30-b0001a-1 1 vcc +12v, dc, regulated 2 vcc +12v, dc, regulated 3 vcc +12v, dc, regulated 4 vcc +12v, dc, regulated 5 gnd ground and signal return 6 gnd ground and signal return 7 gnd ground and signal return 8 gnd ground and signal return 9 lvds option open/high(3.3v) for ns, low(gnd) for jeida 10 reserved nc(aging)auo internal test 11 gnd ground and signal return for lvds 12 rin0- lvds channel 0 negative 13 rin0+ lvds channel 0 positive 14 gnd ground and signal return for lvds 15 rin1- lvds channel 1 negative 16 rin1+ lvds channel 1 positive 17 gnd ground and signal return for lvds 18 rin2- lvds channel 2 negative 19 rin2+ lvds channel 2 positive 20 gnd ground and signal return for lvds 21 rclk- lvds clock negative 22 rclk+ lvds clock positive 23 gnd ground and signal return for lvds 24 rin3- lvds channel 3 negative 25 rin3+ lvds channel 3 positive 26 gnd ground and signal return for lvds 27 reserved nc (auo internal test) 28 reserved nc (auo internal test) 29 gnd ground and signal return 30 gnd ground and signal return free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 10 / 30 ? lvds option = high/open ? ?? ? ns b bb b2 22 2 na nana na de dede de de dede de b bb b2 22 2 b bb b3 33 3 b bb b4 44 4 b bb b5 55 5 na nana na b bb b3 33 3 r rr r0 00 0 r rr r5 55 5 g gg g0 00 0 g gg g0 00 0 r rr r0 00 0 r rr r1 11 1 r rr r2 22 2 r rr r3 33 3 r rr r4 44 4 r rr r1 11 1 g gg g1 11 1 b bb b0 00 0 b bb b1 11 1 b bb b1 11 1 g gg g1 11 1 g gg g2 22 2 g gg g3 33 3 g gg g4 44 4 g gg g5 55 5 g gg g2 22 2 clock clock clock clock chx chx chx chx_ __ _0 00 0+ ++ + chx chx chx chx_ __ _0 00 0- -- - chx chx chx chx_ __ _1 11 1+ ++ + chx chx chx chx_ __ _1 11 1- -- - chx chx chx chx_ __ _2 22 2+ ++ + chx chx chx chx_ __ _2 22 2- -- - chx chx chx chx_ __ _3 33 3+ ++ + chx chx chx chx_ __ _3 33 3- -- - r rr r6 66 6 b bb b7 77 7 na nana na na nana na r rr r6 66 6 r rr r7 77 7 g gg g6 66 6 g gg g7 77 7 b bb b6 66 6 r rr r7 77 7 previous cycle curre nt cycle next cycle previous cycle curre nt cycle next cycle previous cycle curre nt cycle next cycle previous cycle curre nt cycle next cycle note: x = 1, 2, 3, 4 ? lvds option = low ? ?? ? jeida b bb b4 44 4 na nana na de dede de de dede de b bb b4 44 4 b bb b5 55 5 b bb b6 66 6 b bb b7 77 7 na nana na b bb b5 55 5 r rr r2 22 2 r rr r7 77 7 g gg g2 22 2 g gg g2 22 2 r rr r2 22 2 r rr r3 33 3 r rr r4 44 4 r rr r5 55 5 r rr r6 66 6 r rr r3 33 3 g gg g3 33 3 b bb b2 22 2 b bb b3 33 3 b bb b3 33 3 g gg g3 33 3 g gg g4 44 4 g gg g5 55 5 g gg g6 66 6 g gg g7 77 7 g gg g4 44 4 clock clock clock clock r rr r0 00 0 b bb b1 11 1 na nana na na nana na r rr r0 00 0 r rr r1 11 1 g gg g0 00 0 g gg g1 11 1 b bb b0 00 0 r rr r1 11 1 chx chx chx chx_ __ _0 00 0+ ++ + chx chx chx chx_ __ _0 00 0- -- - chx chx chx chx_ __ _1 11 1+ ++ + chx chx chx chx_ __ _1 11 1- -- - chx chx chx chx_ __ _2 22 2+ ++ + chx chx chx chx_ __ _2 22 2- -- - chx chx chx chx_ __ _3 33 3+ ++ + chx chx chx chx_ __ _3 33 3- -- - previous cycle curre nt cycle next cycle previous cycle curre nt cycle next cycle previous cycle curre nt cycle next cycle previous cycle curre nt cycle next cycle note: x = 1, 2, 3, 4 free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 11 / 30 3-3 signal timing specification this is the signal timing required at the input of the user connector. all of the interface signal tim ing should be satisfied with the following specifications for its proper operation. signal item symbol min. typ. max unit period tv 784 810 1015 th active tdisp (v) 768 th vertical section blanking tblk (v) 16 42 247 th period th 1460 1648 2000 tclk active tdisp (h) 1366 tclk horizontal section blanking tblk (h) 94 282 634 tclk clock frequency fclk=1/tclk 50 80 86 mhz vertical frequency frequency fv 47 60 63 hz horizontal frequency frequency fh 43 48 53 khz notes: (1) display position is specific by the rise of de signal only. horizontal display position is specified by the ris ing edge of 1 st dclk after the rise of 1 st de, is displayed on the left edge of the screen. (2) vertical display position is specified by the r ise of de after a low level period equivalent to eight times of horizontal period. the 1 st data corresponding to one horizontal line after th e rise of 1 st de is displayed at the top line of screen. (3) if a period of de ?igh?is less than 1,366 dcl k or less than 768 lines, the rest of the screen di splays black. (4) the display position does not fit to the screen if a period of de high and the effective data pe riod do not synchronize with each other. free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 12 / 30 3-4 signal timing waveforms th tdisp(v) tblk(v) tv de rgb data line n invalid data invalid data line 1 line 2 line 3 line n line 4 tclk clk de ch1 pixel m-3 pixel m-2 pixel m-1 pixel m invalid data pixel 1 pixel 2 pixel 3 pixel 4 pixel 5 pixel 6 pixel m-2 pixel m-1 pixel m invalid data pixel 1 pixel 2 th tdisp(h) tblk(h) m m m m p p p p i i i i x x x x e e e e l l l l n line n line n line n line free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 13 / 30 3-5 color input data reference the brightness of each primary color (red, green an d blue) is based on the 8 bit gray scale data input for the color; the higher the binary input, the brighter th e color. the table below provides a reference for c olor versus data input. ? color data reference input color data red msb lsb green msb lsb blue msb lsb color r7 r6 r5 r4 r3 r2 r1 r0 g7 g6 g5 g4 g3 g2 g1 g0 b7 b6 b5 b4 b3 b2 b1 b0 black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 ye ll o w 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 basic color white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ---- red(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 r red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 ---- green(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 g green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 blue(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 ---- blue(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 b blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 14 / 30 3-6 power sequence for lcd values parameter min. type. max. unit t1 0.4 --- 30 ms t2 0.1 --- --- ms t3 200 --- --- ms t4 0 *1 --- --- ms t5 0 --- --- ms t6 --- --- --- *2 ms t7 500 --- --- ms note: (1) t4=0 : concern for residual pattern before blu turn off. (2) t6 : voltage of vdd must decay smoothly after p ower-off. (customer system decide this value) free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 15 / 30 3-7 backlight specification (inverter type) the backlight unit contains 4u ccfls (cold cathode fluorescent lamp) 3-7-1 electrical specification spec item symbol condition min. typ. max. unit note input voltage v ddb - 21.6 24 26.4 vdc -- input current i ddb vddb=24v 3.09 3.25 3.41 adc 1 input power p ddb vddb=24v 74.1 78 81.9 w 1 inrush current i rush vddb=24v -- -- 5.25 adc 2 operating frequency fbl vddb=24v 53 55 57 khz -- on 2 -- 5.5 -- on/off control voltage v blon off vddb=24v 0 -- 0.8 vdc -- on/off control current i blon vddb=24v -- -- 1.5 ma -- max 3.0 -- 3.3 vdc -- internal pwm dimming control voltage v_ipw m min vddb=24v -- 0 -- vdc -- internal pwm dimming control current i_ipwm vddb=24v -- -- 2 madc -- internal pwm dimming ratio r_ipwm vddb=24v 10 -- 100 % -- max vddb=24v 2 -- 3.3 -- external pwm control voltage v_ep wm min vddb=24v 0 -- 0.8 vdc -- external pwm control current i_epwm vddb=24v -- -- 2 madc -- external pwm duty ratio d_epwm vddb=24v 10 -- 100 % 3 external pwm frequency f_epwm vddb=24v 120 150 240 hz -- note 1 : dimming ratio= 100% (max) ta =2 5 5 , tu r n o n f o r 4 5m i n u t es note 2 : measurement condition rising time = 20ms ( vddb : 10%~90%); note 3 : for external pwm application, 5% dimming is function well and no backlight shutdo wn. free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 16 / 30 3-7-2 input pin assignment ? inverter connector: ci0114m1hrl-nh (cvilux) note : if external pwm function includes 5% dimming ratio. judge condition as below: (1) backlight module must be lighted on normally. (2) all protection function must work normally. (3) uniformity and flicker could not be guaranteed pin symbol description 1 vddb operating voltage supply, +24v dc regulated 2 vddb operating voltage supply, +24v dc regulated 3 vddb operating voltage supply, +24v dc regulated 4 vddb operating voltage supply, +24v dc regulated 5 vddb operating voltage supply, +24v dc regulated 6 blgnd ground and current return 7 blgnd ground and current return 8 blgnd ground and current return 9 blgnd ground and current return 10 blgnd ground and current return 11 det blu status detection: normal : 0~0.8v ; abnormal : open collector 12 vblon blu on-off control: high/open (3.3v~5.5v) : bl on ; low (0~0.8v/gnd) : bl off 13 vdim internal pwm (0~3.3v for 10~100% duty, open for 100 %) < nc ; at external pwm mode> 14 pdim external pwm (10%~100% duty, open for 100%) < nc ; at internal pwm mode> free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 17 / 30 3-7-3 power sequence for inverter power input for blu (vddb) dimming control signal (vdim) blu on/off enable (vblon) 24v(typ.) 10% 90% 90% t1 t2 t3 t4 t5 power input for blu (vddb) dimming control signal (vdim) blu on/off enable (vblon) 24v(typ.) 10% 90% 90% t1 t2 t3 t4 t4 t5 ? dip condition for inverter power input for blu (vddb) t6 vddb(typ.)*0.8 power input for blu (vddb) t6 vddb(typ.)*0.8 value parameter min typ max units t1 20 - - ms t2 500 - - ms t3 250 - - ms t4 0 - - ms t5 1 - - ms t6 - - 10 ms free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 18 / 30 4. optical specification optical characteristics are determined after the un it has been ?n and stable for approximately 45 mi nutes in a dark environment at 25c. the values specified are at an approximate distance 50cm from the lcd surfac e at a viewing angle of and equal to 0. fig.1 presents additional information concerning th e measurement equipment and method. values parameter symbol min. typ. max unit notes contrast ratio cr 2,400 3,000 -- -- 1 surface luminance (white) l wh 350 420 -- cd/m 2 2 luminance variation white(9p) -- -- 1.3 -- 3 response time (g to g) t -- 6.5 -- ms 4 color gamut ntsc -- 72 -- % -- red r x 0.64 -- -- r y 0.33 -- -- green g x 0.29 -- -- g y 0.60 -- -- blue b x 0.15 -- -- b y 0.06 -- -- white w x 0.280 -- -- color coordinates w y typ.-0.03 0.290 typ.+0.03 -- -- x axis, right( =0) r -- 89 -- degree 5 x axis, left( =180) l -- 89 -- degree 5 y axis, up( =90) u -- 89 -- degree 5 viewing angle y axis, down ( =270) d -- 89 -- degree 5 sr3 or equivalent free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 19 / 30 note: 1. contrast ratio (cr) is defined mathematically as : surface luminance of l on5 contrast ratio= surface luminance of l off5 2. surface luminance is luminance value at point 5 across the lcd surface 50cm from the surface with a ll pixels displaying white. from more information see fig 2.l wh =lon5 where lon5 is the luminance with all pixels displaying white at center 5 location. fig 2 luminance 3. the variation in surface luminance, white is defined (center of screen) as: white(9p) = maximum(l on1 , l on2 ,,l on9 )/ minimum(l on1 , l on2 ,l on9 ) 4. response time t is the average time required for display transition by switching the input signal for five luminance ratio (0%,25%,50%,75%,100% brightness mat rix) and is based on f v =60hz to optimize. target measured response time 0% 25% 50% 75% 100% 0% 0% to 25% 0% to 50% 0% to 75% 0% to 100% 25% 25% to 0% 25% to 50% 25% to 75% 25% to 100% 50% 50% to 0% 50% to 25% 50% to 75% 50% to 100% 75% 75% to 0% 75% to 25% 75% to 50% 75% to 100% start 100% 100% to 0% 100% to 25% 100% to 50% 100% to 75% 1 2 3 4 5 6 7 8 h v h/6 h/2 v/2 v/6 free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 20 / 30 5. viewing angle is the angle at which the contrast ratio is greater than 10. the angles are determine d for the horizontal or x axis and the vertical or y axis wit h respect to the z axis which is normal to the lcd surface. for more information see fig 3. fig 3 viewing angle free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 21 / 30 5. mechanical characteristics the contents provide general mechanical characteris tics for the model t315xw03 v3. in addition the fig ures in the next page are detailed mechanical drawing of th e lcd. horizontal 760.0mm vertical 450.0mm outline dimension depth 46.9mm (w/ inverter & shielding) horizontal 703.8mm bezel opening vertical 398.4mm horizontal 697.685mm active display area vertical 392.256mm weight 5,000 g (typ.) surface treatment ag, haze=11%, 3h free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 22 / 30 ? front view free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 23 / 30 ? back view free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 24 / 30 6. reliability test items no. test item qty condition 1 high temperature storage test 3 60 , 300hrs 2 low temperature storage test 3 -20 , 300hrs 3 high temperature operation test 3 50 , 300hrs 4 low temperature operation test 3 -5 , 300hrs 5 vibration test (non-operation) 3 wave form : random vibration level : 1.5g rms bandwidth: 10-300hz duration: x, y, z 30min one time for each direction 6 shock test (non-operation) 3 shock level: 50g waveform: half since wave, 11ms direction: x, y, z, one time each direction 7 vibration test (with carton) 3 random wave (1.5g rms, 10-200hz) 30mins/ per each x,y,z axes 8 drop test (with carton) 3 height: 45.7 cm 1 corner, 3 edges, 6 surfaces (astm-d5276) free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 25 / 30 7. international standard 7-1 safety (1) ul 60950-1, ul 60065; standard for safety of in formation technology equipment including electrical business equipment. (2) iec 60950-1 : 2001, iec 60065:2001 ; standard f or safety of international electrotechnical commiss ion (3) en 60950 : 2001+a11, en 60065:2002+a1:2006; eur opean committee for electrotechnical standardization (cenelec), european standard for sa fety of information technology equipment including electrical business equipment. 7-2 emc (4) ansi c63.4 ?ethods of measurement of radio-noi se emissions from low-voltage electrical and electrical equipment in the range of 9khz to 40ghz. american national standards institute(ansi), 1992 (5) c.i.s.p.r ?imits and methods of measurement of radio interface characteristics of information technolog y e qu ipm ent. int ernati on al spec ia l com m it tee on radio interference. (6) en 55022 ?imits and methods of measurement of radio interface characteristics of information technolog y e qu ipm ent. eu ropea n com m ittee f or el ect rotechnical standardization. (cenelec), 1998 free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 26 / 30 8. packing 8-1 definition of label ? panel label *xxxxxxxxxxxx -xxxxxx * green mark description (1) for pb free product, auo will add for identification. (2) for rohs compatible products, auo will add rohs for identification. note: the green mark will be present only when the green documents have been ready by auo internal gre en team. (definition of green design follows the auo g reen design checklist.) ? carton label au optronics *xxxxxxxxxxxx-xxxxxx* t315xw03 v.3 97.31t08.xxx qty : 4 *xxxxxx-xxxxxxxxxx* xxxxx model no: t315xw03 v.3 xx xxxxx manufactured xx / xx made in xxxxx auo internal use week year panel unique id auo internal use factory location auo internal use free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 27 / 30 8-2 packing methods: 4pcs modules 1pc module/esd bag module cushion set ?h ?tape free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 28 / 30 8-3 pallet and shipment information specification item quantity dimension weight (kg) packing remark 1 packing box 4pcs/box 832(l)mm*283(w)mm*545(h)mm 24.1 2 pallet 1 1150(l)mm*840(w)mm*132(h)mm 13 3 boxes per pallet 8 boxes/pallet 4 panels per pallet 32pcs/pallet 5 pallet after packing n/a 1150(l)mm*840(w)mm*1222(h)mm 205.8 stretch film label corner angle pet band moisture-proof film corner angle pallet free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 29 / 30 9. precautions please pay attention to the followings when you use this tft lcd module. 9-1 mounting precautions (1) you must mount a module using holes arranged in four corners or four sides. (2) you should consider the mounting structure so t hat uneven force (ex. twisted stress) is not applie d to module. and the case on which a module is mounted s hould have sufficient strength so that external for ce is not transmitted directly to the module. (3) please attach the surface transparent protectiv e plate to the surface in order to protect the pola rizer. transparent protective plate should have sufficient strength in order to the resist external force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials fo r the cover case are not desirable because the form er generates corrosive gas of attacking the polarizer at high temperature and the latter cause circuit br oken by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizer with glass, tweezers or anything harder than hb pe ncil lead. and please do not rub with dust clothes with chemical treatment. do not touch the surface of pol arizer for bare hand or greasy cloth. (some cosmetics are detrimental to the polarizer.) (7) when the surface becomes dusty, please wipe gen tly with absorbent cotton or other soft materials l ike chamois soaks with petroleum benzene. normal-hexane is recommended for cleaning the adhesives used to attach front/ rear polarizer. do not use acetone , toluene and alcohol because they cause chemical damage to the polarizer. (8) wipe off saliva or water drops as soon as possi ble. their long time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. 9-2 operation precautions (1) the device listed in the product specification sheets was designed and manufactured for tv applica tion (2) the spike noise causes the mis-operation of cir cuits. it should be lower than following voltage: v=200mv(over and under shoot voltage) (3) response time depends on the temperature. (in l ower temperature, it becomes longer..) (4) brightness of ccfl depends on the temperature. (in lower temperature, it becomes lower.) and in lo wer temperature, response time (required time that brig htness is stable after turned on) becomes longer. (5) be careful for condensation at sudden temperatu re change. condensation makes damage to polarizer o r electrical contacted parts. and after fading conden sation, smear or spot will occur. (6) when fixed patterns are displayed for a long ti me, remnant image is likely to occur. (7) module has high frequency circuits. sufficient suppression to the electromagnetic interference sha ll be done by system manufacturers. grounding and shieldi ng methods may be important to minimize the interface. free datasheet http://www..net/
t315xw03 v3 product specification rev. 1.0 ?copyright auo optronics corp. 2009 all rights res erved. page 30 / 30 9-3 electrostatic discharge control since a module is composed of electronic circuits, it is not strong to electrostatic discharge. make c ertain that treatment persons are connected to ground through w ristband etc. and dont touch interface pin directl y. 9-4 precautions for strong light exposure strong light exposure causes degradation of polariz er and color filter. 9-5 storage when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the m odule to sunlight or fluorescent light. keep the te mperature between 5 and 35 at normal humidity. (2) the polarizer surface should not come in contac t with any other object. it is recommended that the y be stored in the container in which they were shipped. 9-6 handling precautions for protection film (1) the protection film is attached to the bezel wi th a small masking tape. when the protection film i s peeled off, static electricity is generated between the fi lm and polarizer. this should be peeled off slowly and carefully by people who are electrically grounded a nd with well ion-blown equipment or in such a condi tion, etc. (2) when the module with protection film attached i s stored for a long time, sometimes there remains a very small amount of glue still on the bezel after the p rotection film is peeled off. (3) you can remove the glue easily. when the glue r emains on the bezel or its vestige is recognized, p lease wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexan e. free datasheet http://www..net/

▲Up To Search▲

Price & Availability of T315XW03-V3

	To Download T315XW03-V3 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .